Brass-Toned Ribbed Furniture Connector Pair — Two brass-toned ribbed furniture connector components shown as a flanged hollow sleeve and a matching locating-pin form. Final component geometry, panel and hole interfaces, mating parts, material, finish, quantity and packaging require confirmation.
Product Overview
| Photographed Configuration | Two brass-toned ribbed furniture connector components shown as a flanged hollow sleeve and a matching locating-pin form. |
|---|---|
| Purchasing Position | Furniture connector or support assembly requiring panel, hole, mating-component and installation confirmation. |
| Order Boundary | Photographed colors, dimensions and quantities do not define the production order. |
| Quotation Basis | Approved drawing or sample, mating part or panel, installation conditions, quantity, packaging and acceptance criteria. |
Specifications & Custom Capability
Current Product Configuration
| Product Type | Brass-Toned Ribbed Furniture Connector Pair |
|---|---|
| Current Product Configuration | Two brass-toned ribbed furniture connector components shown as a flanged hollow sleeve and a matching locating-pin form. |
| Primary Form | Two-part press-fit furniture connector using ribbed outside profiles for retention in prepared panel holes. |
| Head / Interface | Confirm sleeve flange, bore, outside ribs, body length and entry edge together with pin diameter, nose, shoulders and mating depth. |
| Thread / Mating Part | No thread is visibly confirmed; specify whether the final pair is press-fit, threaded or otherwise retained and provide both mating components. |
| Current Appearance | Brass-toned surfaces are shown; confirm base materials, finish or plating, color range and service environment. |
| Material | Confirm according to drawing, sample or purchase specification. |
| Installation | Confirm panel materials, hole diameters and depths, interference or clearance, insertion direction, assembly sequence and buyer test. |
| Dimensions & Tolerances | Confirm according to drawing, sample or purchase specification. |
Custom Manufacturing & Order Review
| Made-to-Drawing | Available for review with component drawings, panel-hole specification, joint section and mating-component details. |
|---|---|
| Made-to-Sample | Available for comparison with representative connectors, panels, mating parts and approved finish samples. |
| Component Geometry | Cam, pin, support body, sleeve, connector head, shank, shoulder and panel interfaces can be reviewed against the approved furniture joint. |
| Threaded Component Range | Threaded screws or dowels from M1 to M12 can be reviewed only where compatible with the confirmed furniture assembly, material, geometry and installation method. |
| Threaded Component Length | Threaded screws or dowels from 3 mm to 200 mm can be reviewed only where compatible with the confirmed panel, joint, engagement and manufacturing route. |
| Finish Options | Zinc plating, Ruspert coating, spray painting, electrophoretic coating, blackening, gold plating, silver plating and copper plating can be reviewed only where compatible with the confirmed base material, geometry, service environment and acceptance requirement. |
| Packaging & Private Label | Bulk, counted bags, blister packs, compartment cases or private-label cartons can be reviewed after part identity, quantity, protection, labels and artwork are approved. |
| MOQ | 10,000 pcs per confirmed specification |
| Samples | Request a representative sample with the proposed components, panels, holes, finish and packaging specification. |
Applications
| Knock-down furniture joints | Coordinate the sleeve, pin and panel holes as a matched system. |
|---|---|
| Cabinet alignment connections | Confirm installed projection, seating and repeated-assembly requirement. |
| Replacement connector pairs | Compare both components, holes and mating depth with approved samples. |
| OEM furniture hardware bags | Control matched counts, separation, labels and installation instructions. |
Buyer Guide
| Are both photographed components ordered together? | Define the sleeve, pin, ratio and packaging explicitly in the approved BOM. |
|---|---|
| Which hole information is required? | Provide diameter, depth, tolerance, panel material and edge distance for both sides. |
| Can material be identified from the color? | No. Confirm base material, finish process and approved color sample. |
| How should fit be approved? | Use production-representative panels and a buyer-specified insertion, retention and assembly test. |
Quality Control
| Sleeve geometry | Inspect flange, bore, ribs, body, entry edge and visible surface. |
|---|---|
| Pin geometry | Check nose, shoulders, diameter, straightness and mating depth. |
| Panel assembly trial | Verify insertion, seating, alignment, retention and specified test. |
| Pair and pack audit | Confirm component ratio, count, separation, label and protection. |
Packaging & Customization
| Packaging Format | Bulk, counted bags, blister packs, compartment cases or private-label cartons can be reviewed after part identity, quantity, protection, labels and artwork are approved. |
|---|---|
| Identification | Use approved item codes, quantities, labels, barcodes and carton marks. |
| Component Protection | Prevent mixed parts, movement and visible-surface damage through the confirmed pack design. |
| Private Label | Submit approved artwork, language, barcode data and legal marking requirements before production. |
Frequently Asked Questions
| Is the order limited to the photographed furniture component? | No. The gallery records the current photographed configuration. Final component geometry, panel and hole interfaces, mating parts, material, finish, quantity and packaging require an approved drawing or sample. |
|---|---|
| Can the furniture connector or support geometry be customized? | Component geometry can be reviewed against the confirmed panel, hole layout, mating parts and installation method. M1 to M12 threads and 3 mm to 200 mm lengths apply only to compatible screw or dowel components after technical review. |
| Are both photographed components ordered together? | Define the sleeve, pin, ratio and packaging explicitly in the approved BOM. |
| Which finishes can be reviewed for metallic components? | Zinc plating, Ruspert coating, spray painting, electrophoretic coating, blackening, gold plating, silver plating and copper plating can be reviewed only where compatible with the confirmed base material, geometry, service environment and acceptance requirement. |
| Can the package and label be customized? | Bulk, counted bags, blister packs, compartment cases or private-label cartons can be reviewed after part identity, quantity, protection, labels and artwork are approved. |
| What is required for quotation? | Send the component and panel drawings or samples, hole specification, mating parts, installation method, material and finish requirement, quantity and packaging artwork. MOQ starts at 10,000 pcs per confirmed specification. |
Need a Custom Quote?
Send a drawing or sample and the confirmed assembly requirements. JH Fix will review manufacturing compatibility, sample scope and quotation details.
| RFQ 1 | Connector drawings or approved samples |
|---|---|
| RFQ 2 | Sleeve, pin and mating-depth details |
| RFQ 3 | Panel materials, holes and tolerances |
| RFQ 4 | Insertion method and retention test |
| RFQ 5 | Materials, finish and color requirement |
| RFQ 6 | Pair ratio, quantity, labels and packaging |
MOQ: 10,000 pcs per confirmed specification
