Product Overview
| pointed countersunk self-tapping screw | Black cross-drive countersunk screw with deep coarse full-length thread shown and a pointed lead. The photographed configuration is separated from order-dependent material, finish and dimensions. |
|---|---|
| Buying context 1 | The photographs show a deep thread intended for review in timber and engineered-board joints. Edge distance, pilot hole and splitting behavior require trials. |
| Buying context 2 | The flush-seating head and prepared seat, pilot-hole requirement, thread engagement and point clearance must be checked in the actual joint. |
| Procurement note | Diameter, pitch, length and measurement datum; Countersunk head and cross-drive dimensions; Substrate and prepared-hole condition; Required engagement, seating and point clearance; Material, finish and acceptance criteria; Quantity, mating hardware and packaging. |
Specifications & Custom Capability
Use the photographed configuration to identify the product form. Dimensions, materials, finishes and order-dependent requirements are confirmed against the approved drawing, sample or purchase specification.
Current Product Configuration
| Product Type | Pointed countersunk self-tapping screw |
|---|---|
| Head | Countersunk head |
| Drive | Cross recess |
| Thread | Deep coarse full-length thread shown |
| Point | Sharp pointed lead shown |
| Current Appearance | Black; confirm material and surface-treatment specification |
| Material | Confirm according to drawing, sample or purchase specification. |
| Substrate | Specify timber species, engineered board or other receiving material |
| Pilot Hole | Confirm requirement, diameter and depth through representative trials |
| Thread Engagement | Confirm required embedment, edge distance and point clearance |
| Head Seating | Confirm countersink geometry, flushness and surface condition |
| Installation | Confirm driver size, speed or torque method and access |
Custom Manufacturing & Order Review
| Customization Scope | Diameter, pitch, length, point, countersunk head, cross recess, material, finish and packaging can be reviewed against the substrate, pilot hole and joint drawing. |
|---|---|
| Manufacturing Capability | Review diameter, pitch, length, point, head and drive against the approved joint and substrate |
| Made-to-Drawing | Available for review with the screw drawing and a section through the installed joint |
| Made-to-Sample | Available for comparison with a representative screw, substrate and prepared-hole condition |
| Custom Specification Review | Review substrate, pilot hole, engagement, head seating, material, finish and installation requirement before quotation |
| Packaging & Private Label | Bulk cartons, counted packs, assembly kits and label artwork can be reviewed according to the confirmed order specification |
| MOQ | 10,000 pcs per confirmed specification |
| Samples | Request the selected screw for representative insertion, seating and removal trials |
| Custom Thread Range | Self-tapping configurations from M1 to M12 can be reviewed where compatible with the confirmed subtype, substrate and application. |
| Custom Length Range | Lengths from 3 mm to 200 mm can be reviewed according to thread diameter, head geometry, product subtype and purchase specification. |
| Finish Options | Zinc plating, Ruspert coating, spray painting, electrophoretic coating, blackening, gold plating, silver plating and copper plating can be reviewed according to the confirmed material, service environment, appearance and acceptance requirements. |
Applications
| Cabinet and furniture panels | Confirm panel type, pilot hole, edge distance, hardware thickness and final head seating. |
|---|---|
| Hinge and bracket fastening | Match the screw head, hole clearance and required engagement to the selected fitting. |
| Timber or engineered-board joints | Validate insertion, seating and substrate behavior using representative material. |
| Controlled hardware packs | Keep diameter, length, finish and mating hardware under approved part numbers. |
Buyer Guide
| Is a pilot hole required? | That depends on screw geometry, substrate density or thickness, edge distance and installation method. Confirm it through representative trials. |
|---|---|
| Can the head finish flush? | The photographed head is countersunk, but the seat angle, surface behavior and required flushness must be specified and checked. |
| How should thread engagement be selected? | Define it from the substrate, joint stack, point clearance and buyer-specified acceptance criteria. |
| Can the pictured dimensions be changed? | Yes. Select diameter, pitch and length from the approved drawing, substrate and joint requirement rather than treating the photographed size as fixed. |
Quality Control
| Thread and point | Check diameter, pitch, thread depth, usable length, runout and point condition. |
|---|---|
| Head and cross drive | Inspect head dimensions, countersunk seat, recess geometry and driver fit. |
| Installation trial | Review insertion, seating, splitting or breakout, point clearance and removal in the specified substrate. |
| Material and finish | Verify the approved material and surface-treatment requirements and protect threads and points during packing. |
| Acceptance basis | Relevant testing can be reviewed according to the buyer's specified method, mating parts and acceptance criteria. |
Packaging & Customization
| Packaging plan | Use protected bulk cartons, counted bags or assembly kits. Separate diameter, length and finish variants, protect heads and sharp points, and identify approved mating hardware. |
|---|---|
| OEM review | Diameter, pitch, length, point, countersunk head, cross recess, material, finish and packaging can be reviewed against the substrate, pilot hole and joint drawing. |
Frequently Asked Questions
| Is this screw limited to the photographed size? | No fixed pictured size defines the product. Diameter and length are selected according to the approved drawing, substrate and joint requirement. |
|---|---|
| Can diameter, pitch and length be customized? | Self-tapping configurations from M1 to M12 and lengths from 3 mm to 200 mm can be reviewed where compatible with the confirmed subtype and application. |
| Does it always need a pilot hole? | No universal rule is stated. Confirm pilot-hole requirement, diameter and depth through representative trials in the specified substrate. |
| Which finishes can be reviewed? | Zinc plating, Ruspert coating, spray painting, electrophoretic coating, blackening, gold plating, silver plating and copper plating can be reviewed according to the confirmed material, service environment, appearance and acceptance requirements. |
| Is the photographed color proof of the coating? | No. Specify material, coating system, service environment, appearance and acceptance criteria in the purchase specification. |
| What is required for quotation? | Send screw and joint drawings, substrate, pilot hole, engagement, finish, quantity and packaging. MOQ starts at 10,000 pcs per confirmed specification. |
Need a Custom Quote?
| Quotation request | Send the following product-specific information so JH Fix can review an accurate specification and quotation. |
|---|---|
| RFQ item 1 | Diameter, pitch, length and measurement datum |
| RFQ item 2 | Countersunk head and cross-drive dimensions |
| RFQ item 3 | Substrate and prepared-hole condition |
| RFQ item 4 | Required engagement, seating and point clearance |
| RFQ item 5 | Material, finish and acceptance criteria |
| RFQ item 6 | Quantity, mating hardware and packaging |
| Contact | Get a Quote | Send Drawing / Sample | WhatsApp |
| Datasheet | Available after specification confirmation. |
Black cross-drive countersunk screw with deep coarse full-length thread shown and a pointed lead. The photographed configuration is separated from order-dependent material, finish and dimensions.
