Concealed Threaded Floating Shelf Support Rod — Brown concealed shelf-support rods shown with a threaded metal section, polymer wall plug, washer and end cap. Final component geometry, panel and hole interfaces, mating parts, material, finish, quantity and packaging require confirmation.
Product Overview
| Photographed Configuration | Brown concealed shelf-support rods shown with a threaded metal section, polymer wall plug, washer and end cap. |
|---|---|
| Purchasing Position | Furniture connector or support assembly requiring panel, hole, mating-component and installation confirmation. |
| Order Boundary | Photographed colors, dimensions and quantities do not define the production order. |
| Quotation Basis | Approved drawing or sample, mating part or panel, installation conditions, quantity, packaging and acceptance criteria. |
Specifications & Custom Capability
Current Product Configuration
| Product Type | Concealed Threaded Floating Shelf Support Rod |
|---|---|
| Current Product Configuration | Brown concealed shelf-support rods shown with a threaded metal section, polymer wall plug, washer and end cap. |
| Primary Form | Hidden support rod installed between a wall fixing and a drilled shelf, with a threaded section for positioning or engagement. |
| Head / Interface | Confirm rod diameter and length, threaded section, wall-plug interface, washer and cap, shelf bore and installed projection. |
| Thread / Mating Part | Confirm thread diameter, pitch, length and engagement together with the wall fixing and shelf-side components. |
| Current Appearance | Brown rod and polymer components with a bright metal threaded section are shown; confirm materials, finishes and colors. |
| Material | Confirm according to drawing, sample or purchase specification. |
| Installation | Confirm wall substrate, prepared hole and plug, shelf material and thickness, bore, spacing, leveling and buyer test method. |
| Dimensions & Tolerances | Confirm according to drawing, sample or purchase specification. |
Custom Manufacturing & Order Review
| Made-to-Drawing | Available for review with component drawings, panel-hole specification, joint section and mating-component details. |
|---|---|
| Made-to-Sample | Available for comparison with representative connectors, panels, mating parts and approved finish samples. |
| Component Geometry | Cam, pin, support body, sleeve, connector head, shank, shoulder and panel interfaces can be reviewed against the approved furniture joint. |
| Threaded Component Range | Threaded screws or dowels from M1 to M12 can be reviewed only where compatible with the confirmed furniture assembly, material, geometry and installation method. |
| Threaded Component Length | Threaded screws or dowels from 3 mm to 200 mm can be reviewed only where compatible with the confirmed panel, joint, engagement and manufacturing route. |
| Finish Options | Zinc plating, Ruspert coating, spray painting, electrophoretic coating, blackening, gold plating, silver plating and copper plating can be reviewed only where compatible with the confirmed base material, geometry, service environment and acceptance requirement. |
| Packaging & Private Label | Bulk, counted bags, compartment packs or private-label cartons can be reviewed after component identity, quantity, protection, labels and artwork are approved. |
| MOQ | 10,000 pcs per confirmed specification |
| Samples | Request a representative sample with the proposed components, panels, holes, finish and packaging specification. |
Applications
| Concealed timber shelves | Match rod and bore to the approved shelf section. |
|---|---|
| Wall-mounted display shelving | Confirm substrate, fixing, spacing and alignment. |
| Replacement hidden rods | Compare rod, thread, plug, washer, cap and shelf drilling. |
| OEM shelf hardware sets | Control component ratio, instructions, labels and protection. |
Buyer Guide
| What shelf drilling is required? | Provide bore diameter and depth, shelf material, thickness and edge distances. |
|---|---|
| How is the wall fixing selected? | Use confirmed substrate, hole preparation and buyer-specified installation method. |
| Can load capacity be taken from the source graphic? | No. Define shelf geometry, support spacing, substrate and required test. |
| How is rod projection controlled? | Confirm threaded engagement, wall interface, shelf bore and installed position. |
Quality Control
| Rod and thread | Inspect diameter, length, straightness, thread and surface. |
|---|---|
| Plug, washer and cap | Check geometry, fit, retention, material and condition. |
| Shelf installation trial | Verify wall fixing, bore fit, alignment, projection and specified test. |
| Set audit | Confirm component ratio, instructions, count, label and protection. |
Packaging & Customization
| Packaging Format | Bulk, counted bags, compartment packs or private-label cartons can be reviewed after component identity, quantity, protection, labels and artwork are approved. |
|---|---|
| Identification | Use approved item codes, quantities, labels, barcodes and carton marks. |
| Component Protection | Prevent mixed parts, movement and visible-surface damage through the confirmed pack design. |
| Private Label | Submit approved artwork, language, barcode data and legal marking requirements before production. |
Frequently Asked Questions
| Is the order limited to the photographed furniture component? | No. The gallery records the current photographed configuration. Final component geometry, panel and hole interfaces, mating parts, material, finish, quantity and packaging require an approved drawing or sample. |
|---|---|
| Can the furniture connector or support geometry be customized? | Component geometry can be reviewed against the confirmed panel, hole layout, mating parts and installation method. M1 to M12 threads and 3 mm to 200 mm lengths apply only to compatible screw or dowel components after technical review. |
| What shelf drilling is required? | Provide bore diameter and depth, shelf material, thickness and edge distances. |
| Which finishes can be reviewed for metallic components? | Zinc plating, Ruspert coating, spray painting, electrophoretic coating, blackening, gold plating, silver plating and copper plating can be reviewed only where compatible with the confirmed base material, geometry, service environment and acceptance requirement. |
| Can the package and label be customized? | Bulk, counted bags, compartment packs or private-label cartons can be reviewed after component identity, quantity, protection, labels and artwork are approved. |
| What is required for quotation? | Send the component and panel drawings or samples, hole specification, mating parts, installation method, material and finish requirement, quantity and packaging artwork. MOQ starts at 10,000 pcs per confirmed specification. |
Need a Custom Quote?
Send a drawing or sample and the confirmed assembly requirements. JH Fix will review manufacturing compatibility, sample scope and quotation details.
| RFQ 1 | Support-rod and shelf drawings or samples |
|---|---|
| RFQ 2 | Rod, thread, plug, washer and cap geometry |
| RFQ 3 | Wall substrate, hole and fixing method |
| RFQ 4 | Shelf material, dimensions, bore and spacing |
| RFQ 5 | Materials, finishes, colors and test method |
| RFQ 6 | Set quantity, instructions, labels and packaging |
MOQ: 10,000 pcs per confirmed specification
